2006 Southwest Florida Water Management District (SWFWMD) Lidar: Upper Myakka DistrictView Metadata As: Get Data, FAQ, HTML, 19139 XML
Assess Metadata For: Completeness, DOI Readiness, CSW Readiness, Components
2006 Southwest Florida Water Management District (SWFWMD) Lidar: Upper Myakka District
EarthData International collected ALS-50-derived LiDAR over Upper Myakka Florida with a one-meter post spacing. The period of collection was between 3 October and 12 October 2006. This data set falls in Manatee County. The collection was performed by EarthData Aviation, using a Leica ALS-50 LiDAR system, including an inertial measuring unit (IMU) and a dual frequency GPS receiver. This project required six lifts of flight lines to be collected. The product generated consisted of LiDAR bare earth elevation models in LAS format. This data set is one component of a digital terrain model (DTM) for the Southwest Florida Water Management District’s FY2005 Digital LiDAR Project (H048), encompassing approximately 291 square miles across Manatee County. The 2005 LiDAR dataset is comprised of 3-D mass points delivered in the LAS file format based on the District’s 5,000’ by 5,000’ grid (325 cells). The other DTM component is 2-D and 3-D breakline features in the ESRI ArcGIS Personal Geodatabase format. In accordance with the 2005 SWFWMD Topographic Database Design, the following breakline closed water bodies (lakes, reservoirs, etc) as 3-D polygons; linear hydrographic features (streams, canals, swales, embankments, etc) as 3-D breaklines; coastal shorelines as 3-D linear features; edge of pavement road features as 3-D breaklines; soft features (ridges, valleys, etc.) as 3-D breaklines; obscured vegetation polygons as 2-D polygons; overpasses and bridges as 3-D breaklines; 1-foot contours for visualization purposes; and island features as 3-D polygons. Breakline features were captured to develop a hydrologically correct DTM. Contours (1-foot) were generated from the DTM that meet the National Map Accuracy Standards for 2-foot contours (FEMA specifications). Bare earth LiDAR mass point data display a vertical accuracy of at least 0.3-feet root mean square error (RMSE) in open unobscured areas.

Get the Data
AccessFormat(s)Distributor(s) / Contact InfoInstructions / Constraints
LAZ
Format version: (version is unknown)
DOC/NOAA/NOS/OCM > Office for Coastal Management, National Ocean Service, National Oceanic and Atmospheric Administration, U.S. Department of Commerce
DOC/NOAA/NOS/OCM > Office for Coastal Management, National Ocean Service, National Oceanic and Atmospheric Administration, U.S. Department of Commerce
843-740-1200Mike Sutherland
DOC/NOAA/NESDIS/NGDC > National Geophysical Data Center, NESDIS, NOAA, U.S. Department of Commerce
303-497-6120
7:30am-5:00pm Mountain
Ordering Instructions
The National Geophysical Data Center serves as the archive for this LIDAR data. NGDC should only be contacted for this data if it cannot be obtained from NOAA Coastal Services Center.

The National Geophysical Data Center serves as the archive for this LIDAR dataset. NGDC should only be contacted for the data if it cannot be obtained from NOAA Coastal Services Center.

Use Limitation
These data depict the elevations at the time of the survey and are only accurate for that time. Users should be aware that temporal changes may have occurred since this data set was collected and some parts of this data may no longer represent actual surface conditions. Users should not use this data for critical applications without a full awareness of its limitations. Any conclusions drawn from analysis of this information are not the responsibility of NOAA or any of its partners. These data are NOT to be used for navigational purposes.

Legal Constraints