NCEI (formerly NGDC)
EMMA logo
Back to Collection NOAA/NESDIS/NGDC/MGG/Lidar
View Metadata As: Get Data, FAQ, HTML, 19139 XML
Assess Metadata For: Completeness, DOI Readiness, CSW Readiness, Components

2006 U.S. Geological Survey (USGS) Bare Earth Topographic LiDAR: North Puget Sound, Washington

browse graphicThis kmz file shows the extent of coverage for the 2006 USGS North Puget Sound lidar data set.
USGS Contract Number: 01CRCN0014 In Spring, 2006 Sanborn was contracted by the USGS to survey aprocimately 1,735 square miles of western Whatcom and Skagit Counties in Washington state. All data was collected during ideal conditions (rivers at or below mean level, leaf off, etc.). For this collect two sensors were used: The Leica ALS-50 (High Relief Collection) and Optech 2050 (High and Low Relief Collection). LiDAR calibrations were performed to determine and therefore eliminate systematic biases that occur between the the two sensors. Once the biases were determined they were modeled out. The Leica ALS-50 produced an average point spacing of 1.4 meters. The Optech 2050 produced an average point spacing of 1.3 meters. All points are classified as Class 2 (Ground) which includes water points and any possibly remaining artifacts. Leica ALS-50 LiDAR Acquisition Paramters: Avg. Altitude: 1,500 meters AGL Airspeed: ~120 Knots Scan Freq: 36 Hertz Scan Width Half Angle: 36 Degrees Pulse Rate: 60,000 Hertz Overlap: 44-60% Optech 2050 LiDAR Acquisition Parameters: Avg. Altitude: 1,200 meters AGL Airspeed: ~120 Knots Scan Freq: 30 Hertz Scan Width Half Angle: 40 Degrees Pulse Rate: 50,000 Hertz Overlap: 30-50%
Cite this dataset when used as a source.
Other Access Online access information not available.
Distribution Formats
  • LAZ
Distributor DOC/NOAA/NOS/OCM > Office for Coastal Management, National Ocean Service, National Oceanic and Atmospheric Administration, U.S. Department of Commerce
Dataset Point of Contact Robert Kelly
United States Geological Survey, National Geospatial Technical Operations Center (NGTOC)
Documentation links not available.
  • publication: 2013-01-01
Data Presentation Form: Digital image
Dataset Progress Status Complete
Data Update Frequency: As needed
Purpose: This LiDAR operation was designed to provide a highly detailed ground surface dataset to be used for the development of topographic mapping, contour mapping and hydraulic modeling.
Use Limitations
  • These data depict the elevations at the time of the survey and are only accurate for that time. Users should be aware that temporal changes may have occurred since this data set was collected and some parts of this data may no longer represent actual surface conditions. Users should not use this data for critical applications without a full awareness of its limitations. Any conclusions drawn from analysis of this information are not the responsibility of NOAA or any of its partners. These data are NOT to be used for navigational purposes.
  • While every effort has been made to ensure that these data are accurate and reliable within the limits of the current state of the art, NOAA cannot assume liability for any damages caused by any errors or omissions in the data, nor as a result of the failure of the data to function on a particular system. NOAA makes no warranty, expressed or implied, nor does the fact of distribution constitute such a warranty.
  • DOC/NOAA/NOS/OCM > Office for Coastal Management, National Ocean Service, National Oceanic and Atmospheric Administration, U.S. Department of Commerce
  • DOI/USGS > United States Geological Survey, U.S. Department of the Interior
  • DOC/NOAA/NOS/OCM > Office for Coastal Management, National Ocean Service, National Oceanic and Atmospheric Administration, U.S. Department of Commerce
Time Period: 2006-05-05 to 2006-09-03
Spatial Reference System: urn:ogc:def:crs:EPSG::4269
Spatial Bounding Box Coordinates:
N: 34.576794
S: 32.854996
E: -83.908630
W: -85.215673
Spatial Coverage Map:
Theme keywords none
  • Topography/Bathymetry
  • Elevation
  • Model
  • LiDAR
  • LAS
  • Remote Sensing
Place keywords None
  • US
  • Washington
  • North Puget Sound
  • Whatcom County
  • Skagit County
Use Constraints No constraint information available
Fees Fee information not available.
Lineage information for: dataset
  • DOC/NOAA/NOS/OCM > Office for Coastal Management, National Ocean Service, National Oceanic and Atmospheric Administration, U.S. Department of Commerce
  • DOC/NOAA/NESDIS/NCEI > National Centers of Environmental Information, NESDIS, NOAA, U.S. Department of Commerce
Processing Steps
  • 2006-01-01T00:00:00 - Final post-processing of LiDAR data involves several steps. The airborne GPS data was post-processed using Waypoint's GravNAVTM software (version 7.5). A fixed-bias carrier phase solution was computed in both the forward and reverse chronological directions. The data was processed for both base stations and combined. In the event that the solution worsened as a result of the combination of both solutions the best of both solutions was used to yield more accurate data. The GPS trajectory was combined with the raw IMU data and post-processed using Applanix Inc.'s POSPROC (version 4.3) Kalman Filtering software. This results in a two-fold improvement in the attitude accuracies over the real-time INS data. The best estimated trajectory (BET) and refined attitude data are then reintroduced into the LEICA ALS post processor or REALM Survey Suite OPTECH to compute the laser point-positions. The trajectory is then combined with the attitude data and laser range measurements to produce the 3-dimensional coordinates of the mass points. All return values are produced within ALS Post Processing software or REALM Survey Suite OPTECH software. The multi-return information minus the last return provides a useful depiction of the "canopy" within the project area. The last return is further processed to obtain the "Bare Earth Dataset" as a deliverable. All LiDAR data is processed using the binary LAS format 1.0 file format. LiDAR filtering was accomplished using TerraSolid, TerraScan LiDAR processing and modeling software. The filtering process reclassifies all the data into classes within the LAS formatted file based scheme set using the LAS format 1.0 specifications or by the client. Once the data is classified, the entire data set is reviewed and manually edited for anomalies that are outside the required guidelines of the product specification or contract guidelines, whichever apply. The coordinate and datum transformations were then applied to the data set to reflect the required deliverable projection, coordinate and datum systems as provided in the contract. The final data is in State Plane Washington North Coordinate System with the horizontal and vertical units being in feet.
  • 2013-01-01T00:00:00 - The NOAA Coastal Services Center (CSC) received topographic file in ASCII .XYZ format. The files contained lidar elevation measurements. The data were received in Washington State Plane North Zone 4601, NAD83 coordinates and were vertically referenced to NAVD88 using the Geoid99 model. The vertical units of the data were feet. CSC performed the following processing for data storage and Digital Coast provisioning purposes: 1. The ASCII .XYZ files were converted to LAS version 1.1 using Global Mapper. 2. All points in Class 0 (Never Classified) were changed to Class 2 (Ground). This includes water points. 3. The topographic las files were converted from orthometric (NAVD88) heights to ellipsoidal heights using Geoid99. 4. The topographic las files were converted from a Projected Coordinate System (WA SP North) to a Geographic Coordinate system (GCS). 5. The topographic las files' vertical units were converted from feet to meters. 6. The topographic las files' horizontal units were converted from feet to decimal degrees. 7. The data were converted to LAZ format.
  • 2013-04-25T00:00:00 - The NOAA National Geophysical Data Center (NGDC) received lidar data files via ftp transfer from the NOAA Coastal Services Center. The data are currently being served via NOAA CSC Digital Coast at The data can be used to re-populate the system. The data are archived in LAS or LAZ format. The LAS format is an industry standard for LiDAR data developed by the American Society of Photogrammetry and Remote Sensing (ASPRS); LAZ is a loseless compressed version of LAS developed by Martin Isenburg ( The data are exclusively in geographic coordinates (either NAD83 or ITRF94). The data are referenced vertically to the ellipsoid (either GRS80 or ITRF94), allowing for the ability to apply the most up to date geoid model when transforming to orthometric heights.
Last Modified: 2013-04-25
For questions about the information on this page, please email: